!  Example of a control file using the new RDBE and MARK5C
!  wideband digital backend and recorder.  This is a simple
!  example made by stripping down egrdbe2.key to a basic
!  VLBA schedule.
!
!  A SCHED standard setup file is used.
!
! ==========================================================
! =================  Cover Information  ====================
! ==========================================================
!  Schedule written by Craig Walker

 version = 1
 expt    = 'RDBE test with mixed sidebands'
 expcode = rdbepfb

 piname   = 'Craig Walker'    
 address1 = 'National Radio Astronomy Observatory'  
 address2 = 'P. O. Box O'                           
 address3 = 'Socorro, New Mexico, 87801'
 address4 = ' U.S.A. '
 phone    = '575 835 7247 '    
 obsphone = '575 835 7247 '     
 email    = cwalker@nrao.edu  
 fax      = '575 835 7027 '   
 obsmode  = '6cm 128-4-2 '
 obstype  = VLBA
 note1    = ' ' 
! ==========================================================
! ==============  Correlator Information  ==================
! ==========================================================
!  Note that enough channels should be requested to have channel
!  bandwidths of no more than 0.5 MHz.  Otherwise there is risk
!  of smearing the data because of uncertainties in the a priori
!  delays used for correlation.
 
correl   = Socorro
coravg   = 2
corchan  = 64
cornant  = 2
corpol   = on
corwtfn  = uniform
corsrcs  = standard
cortape  = FTP
corship1 = 'Craig Walker'
corship2 = 'P. O. Box O'
corship3 = 'Socorro NM 87801'

! ==========================================================
! ==================  Program control  =====================
! ==========================================================
!    Normally SCHED will not overwrite preexisting files. 
!    If you want this protection, comment this following line.
 overwrit

!    Set the items desired in the scan listing in the .sum file.
 sumitem  = el1, early

! ==========================================================
! ======= Standard Source and Station Catalogs  ============
! ==========================================================
!    Be sure to use the station and freq files that have the
!    right hardware specifications and IF bandwidth for the
!    RDBE/MARK5C system.  These are not the SCHED defaults (yet).

srcfile  = $SCHED/catalogs/sources.vlba
freqfile = $SCHED/catalogs/freq_RDBE.dat
stafile  = $SCHED/catalogs/stations_RDBE.dat

! ==========================================================
! =======================  Setup files  ====================
! ==========================================================
! Use the standard SCHED setup file for a band near the old
! 6cm standard frequency.

setup = $SCHED/setups/rdbe_pfb_4980_dual.set

! ==========================================================
! =================  Initial Scan Information  =============
! ==========================================================

year     = 2010
month    = 12
day      = 3
start    = 15:30:00

! ==========================================================
! ========================  The Scans  =====================
! ==========================================================
!          Interferometer schedules

!          Demonstrate PREEMPT while at it for optional ends
!          and protection from losing USNO for PT and MK
!          Start with a few optional VLBA scans at the start:
preempt = extra

stations = VLBA_HN, VLBA_LA, VLBA_PT, VLBA_BR, VLBA_MK

dwell = 4:40  gap =  20

source = '3C279' /
source = '3C273' /
source = '3C279' /

! Into the core and protect against USNO preemption:
preempt = no

group=18 rep=2

dwell = 4:40  gap =  20

group = 2  rep = 5
source = '3C279' /
source = '3C273' /


! Loop over M87 and M84, but ending on M87
group = 2  rep = 5
source = 'M87' /
source = 'M84' /
source = 'M87  /

! Allow preemption at the end.
preempt = 'ok'
group = 2  rep = 5
source = 'M87' /
source = 'M84' /
source = 'M87  /